Inland Coatings - Hypalon Single Ply 10 Year System Warranty Requirements

PO Box 247
Adel, IA 50003
Phone: 800-456-8467
Fax: 515-993-4324
Email: info@inlandcoatings.com

Hypalon Single Ply 10 Year System Warranty Requirements [Introduction] [Approved Contractor] [Preliminary Review]
[Specs and Requirements] [Inspections] [Completion]
1. Introduction
The following links and information provide guidance in proper application methods and document submittal procedures for issuance of the "Inland Hypalon Single Ply Roof 10 Year System Warranty". This warranty is not applicable to residential installations or any installation under 100 squares in size. Additionally, Inland's System Warranties are only available to Approved Contractors.

2. Approved Contractor Status
If you are not currently an Inland Approved Contractor, the following forms must be submitted.

Approved Contractor Application
Approved Contractor Agreement

3. Preliminary Project Review
Immediately after contract award, a complete and accurate Bid Report must be submitted to the Inland Warranty Department for approval. This should include pages 1, 2 and 3 of the Inland Project Profile, with a drawing of the roof and the following pictures with detailed descriptions:

Distant shot of entire building.
Roof height shot of overall project.
Close-up of horizontal and vertical seams.
Any unusual flashing or problem areas.

Project Profile (pdf)

A project approval letter must be received from Inland prior to beginning a System Warranted Project. All Project Review pictures and documents should be sent to the following address:

Inland Coatings Corporation
Warranty Department
P.O. Box 247
26259 Hwy 6
Adel, IA 50003

4. Specifications, Requirements, and Estimating
For proper application procedures, please refer to Inland Specification #ISP275H and "General Requirements". We have also provided a link for basic Spray Equipment Recommendations.

ISP275H Specification (pdf)
General Requirements (pdf)
Spray Equipment Recommendations (pdf)
Round Penetration Detail Drawing (pdf) (Viewable JPG version)
Ridge Cap Detail Drawing (pdf) (Viewable JPG version)

5. Inspections
Inland requires two inspections on each system warranted project. The first inspection is conducted at the beginning of the project, after all surface preparation is completed, and prior to the application of any Inland products. Any necessary training issues will be conducted at this time. The second inspection will be conducted at the end of the project, after all product applications are completed.

Contractor shall provide the Inland Warranty Department at least two (2) weeks notice for scheduling of on-site inspections.

Please refer to the Inspection Zone Chart to determine the appropriate charge per inspection.

Inspection Zone Chart (pdf)
Inspection Zone Map

The Inspection Charges must be submitted to Inland, and the initial inspection scheduled, before the start of the project to ensure that the inspections can be performed at the appropriate times. Inspection charges should be submitted to the following address:

Inland Coatings Corporation
Warranty Department
P.O. Box 247
26259 Hwy 6
Adel, IA 50003

6. Projection Completion - Issuing of Warranty
At project completion, a Warranty Submittal Packet must be assembled containing the following forms and information.

The System Warranty should be completed and signed by both the "Approved Inland Contractor" and the building owner or "Owners Representative". The original, signed copy must be sent to Inland Coatings Corp.

Hypalon Single Ply 10 Year System Warranty (pdf)

The "Warranty Certification Statement" must be completed and signed by the Approved Inland Contractor".

Warranty Certification Statement (pdf)

Pages 3 through 5 of the "Inland Project Profile" should be completed. This to include attaching copies of invoices, project pictures, etc.

Project Profile (pdf)

The Roof System Warranty Fees Form should be printed out and completed. A check payable to "Inland Coatings Corporation" should be attached to the form.

Roof System Warranty Fees Form (pdf)

Prior to mailing the warranty submittal packet, please refer to the "Warranty Checklist". This will ensure that all necessary information and documents are properly submitted.

Warranty Checklist (pdf)

The completed Warranty Submittal Packet should be sent to Inland Coatings Corporation at the following address:

Inland Coatings Corporation
Warranty Department
P.O. Box 247
26259 Hwy 6
Adel, IA 50003